8MM FORUM WORLDWIDE • View topic - looking for source for Elmo 16-CL rollers

8MM-16MM FORUM WORLDWIDE

The International Forum for 8mm, 16mm, and 9.5mm film
Dedicated To Collectors Around The World
It is currently Fri Mar 29, 2024 9:55 am

All times are UTC - 5 hours [ DST ]

Click on any of the boxes below to link to a new page



Screening Rooms    Ebay Film Sellers    Film/Equipment Sellers    Laurel and Hardy    Magnetic Striping


Our mission is to provide a "free" forum for all members. This forum will not delete, lock up, or edit any posts. On this forum, you are "free" to question any statement that is not understood, and debate any differences you have with another member. We only moderate when a member will not back up his accusations. There are no condescending attitudes from the Administrator or the Moderator. You will be treated with respect. Dan Lail, Admin. and Chris Smith, Moderator



Post new topic Reply to topic  [ 13 posts ]  Go to page 1, 2  Next
Author Message
 Post subject: looking for source for Elmo 16-CL rollers
PostPosted: Sun Nov 16, 2014 6:48 pm 
Offline
Film Expert
User avatar

Joined: Sun Nov 16, 2014 3:54 am
Posts: 7
Location: Shelby, AL
Hi guys... I have been looking for a 16mm projector for several years and I finally found an Elmo 16-CL at a hamfest with a "Make Offer" sign. I wound up giving the guy $15 for it, knowing that the rollers needed replacing. Not knowing anything aboyut projectors, I didn't know how hard these would be to track down! I don't suppose anyone has, or knows where I can get a set of rollers for this projector?

Any help will be greatly appreciated! Thanks in advance.

_________________
Derek Tombrello
www.RobotsAndComputers.com


Top
 Profile Send private message  
 
 Post subject: Re: looking for source for Elmo 16-CL rollers
PostPosted: Mon Nov 17, 2014 11:27 pm 
Offline
Moderator
User avatar

Joined: Thu May 26, 2011 10:25 am
Posts: 641
Location: Aston, Pa.
Derek, which rollers are you referring to? Could you post a snap of what you need. I think I may have a 16-CL parts machine somewhere around here.


Top
 Profile Send private message  
 
 Post subject: Re: looking for source for Elmo 16-CL rollers
PostPosted: Wed Nov 19, 2014 1:02 am 
Offline
Film Expert
User avatar

Joined: Sun Nov 16, 2014 3:54 am
Posts: 7
Location: Shelby, AL
Sorry... not getting emails about new posts :(

Pretty much all of the rubber rollers, I think. I will try to get a photo (or three) tomorrow and post them. I must warn you, though, that while I am quite proficient with electronics, not so much with optical projectors! lol.. Thanks.

_________________
Derek Tombrello
www.RobotsAndComputers.com


Top
 Profile Send private message  
 
 Post subject: Re: looking for source for Elmo 16-CL rollers
PostPosted: Wed Nov 19, 2014 6:36 pm 
Offline
Film Expert
User avatar

Joined: Sun Nov 16, 2014 3:54 am
Posts: 7
Location: Shelby, AL
OK... like I said... I don't know a lot about projectors, but I think that these are the four that I need. I have seen online that some Elmo 16-CL projectors may have five rollers, but I don't see a fifth. These four, however, are definitely bad! Thanks...


Attachments:
dscf1013 (copy).jpg
dscf1013 (copy).jpg [ 106.24 KiB | Viewed 5022 times ]

_________________
Derek Tombrello
www.RobotsAndComputers.com
Top
 Profile Send private message  
 
 Post subject: Re: looking for source for Elmo 16-CL rollers
PostPosted: Tue Dec 16, 2014 12:25 am 
Offline
Film Expert
User avatar

Joined: Sun Nov 16, 2014 3:54 am
Posts: 7
Location: Shelby, AL
I was just wondering if you ever happened to have a chance to see if you had a set of these? Thanks and Merry Christmas everyone :)

_________________
Derek Tombrello
www.RobotsAndComputers.com


Top
 Profile Send private message  
 
 Post subject: Re: looking for source for Elmo 16-CL rollers
PostPosted: Tue Dec 16, 2014 4:00 pm 
Offline
Film Expert

Joined: Thu Jun 02, 2011 7:15 pm
Posts: 129
Location: Flint Michigan
Greetings
On the Elmo 16CL opt it takes 4 rollers on the mag it takes 5 rollers
Question on th lagre roller with the flange there are 2 types that fit on the shaft
One is a reg and the other is spring loaded
To find the one you need you have to take it off
Spring or no spring ???
i have a few left and planing on geeting more

Hope this helps

RC

_________________
RC's Classic Collections 16mm
Parts & Service
http://www.rcsclassic16mm.com/


Top
 Profile Send private message  
 
 Post subject: Re: looking for source for Elmo 16-CL rollers
PostPosted: Tue Dec 16, 2014 10:09 pm 
Offline
Film Expert
User avatar

Joined: Sun Nov 16, 2014 3:54 am
Posts: 7
Location: Shelby, AL
I will take that off tomorrow or Thursday and get back with you. Thanks!

_________________
Derek Tombrello
www.RobotsAndComputers.com


Top
 Profile Send private message  
 
 Post subject: Re: looking for source for Elmo 16-CL rollers
PostPosted: Tue Dec 16, 2014 10:12 pm 
Offline
Film Expert

Joined: Thu Jun 02, 2011 7:15 pm
Posts: 129
Location: Flint Michigan
Greetings
Ok ill be around
Thank You
RC

_________________
RC's Classic Collections 16mm
Parts & Service
http://www.rcsclassic16mm.com/


Top
 Profile Send private message  
 
 Post subject: Re: looking for source for Elmo 16-CL rollers
PostPosted: Thu Dec 18, 2014 11:21 pm 
Offline
Moderator
User avatar

Joined: Thu May 26, 2011 10:25 am
Posts: 641
Location: Aston, Pa.
Derek--FINALLY located the CL which I find is working and thus won't be a parts machine just yet. Hopefully Richard can locate some of the rollers for you.


Top
 Profile Send private message  
 
 Post subject: Re: looking for source for Elmo 16-CL rollers
PostPosted: Fri Dec 19, 2014 2:22 pm 
Offline
Film Expert
User avatar

Joined: Sun Nov 16, 2014 3:54 am
Posts: 7
Location: Shelby, AL
@Chris... that's cool. I appreciate your looking, though :)

@Richard... I took the roller off (I assume you mean the one on top on the far right) and there is no spring on it.

_________________
Derek Tombrello
www.RobotsAndComputers.com


Top
 Profile Send private message  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 13 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 12 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group